Commercial Roofer in Charlotte, NC

A leak on this building's exterior wall needed to be traced at the roof edge, and punctures in the roof membrane were letting water into the system. The crew opened the wall coping to inspect the membrane below, installed cover…

The flashing around the vent pipes on this shingle roof had failed, the kind of breakdown caused by age, weathering, UV exposure or improper installation. The crew reflashed the pipe penetrations for this roof type, installing new pipe boots and…

A dead valley on this low-slope roof had gaps that exposed the framing, letting water collect at a small gutter. The crew cut new TPO membrane into the valley and both intersecting slopes, heat welded it, and sealed it to…

A roof vent on this shingle roof was leaking because the penetration had not been sealed to the underlayment, giving water a path into the roof. The crew removed the shingles around the vent, sealed the penetration to the underlayment…

The base flashing where this roof meets the wall had failed, the kind of wear caused by age, UV exposure and thermal shock, leaving a path for water. The crew removed the loose flashing material, installed new matching materials as…

A downspout had pulled loose from the gutter outlet, and water was washing down the wall.The crew reset the downspout and sealed the outlet so runoff stays in the drainage line. Photos show the black downspouts seated cleanly on the…

A leak at the bath fan vent on this shingle roof had let water into the deck, leaving a sheet of plywood stained and rotted beneath the shingles. The crew removed the old vent covers, pipe collar and surrounding roofing,…

Damaged asphalt shingles had opened a section of this roof to water, leaving the underlayment exposed beneath the lifted shingles. The crew removed the damaged shingles and installed new ones matching the existing profile and color, with each fastener sealed.…

The membrane had detached from the substrate at the repair area, leaving a three square foot section no longer bonded to the surface below. The detached membrane was re-secured to the substrate and sealed at the perimeter of the repair.…

Existing perimeter coating along the parapet had alligatored across the field with cracking open at one point and an adjacent area worn down to exposed aggregate. A continuous white coating was applied from the parapet base across the deck, covering…

Fasteners, headlaps and vertical seams across the R-panel roof had failing sealant, with rust showing at the penetrations. The roof was powerwashed and stripped of previous sealant, then polyurethane sealant was run at the fasteners, laps and seams and top-coated…

The metal panel roof had weathered across the field, with old patching at the fasteners and panel laps and bare metal showing through. Seams and fastener heads were treated first, then silicone coating was applied over the full field and…

Work was needed at several separate points across the EPDM field, including the curb where a steel column passes through the membrane. Each area was coated in white over the black membrane, carried up onto the column curb and run…

Repaired a hole in a translucent skylight panel on a ribbed metal commercial roof, visible as an open break from the interior below. Filled the damaged section and patched over the opening, then sealed the surrounding area of the panel…

Found five failed penetrations on a low-slope commercial roof where improper flashing left the openings exposed to water entry. Sealed each penetration down to the underlayment and installed new flashing around the openings according to industry standards. Confirmed the penetrations…

Removed deteriorated drain components and repaired the TPO roof drain assembly to restore a watertight seal. Installed new drain hardware, heat-welded TPO flashing, and sealed all termination points to prevent leaks. Verified proper drainage and documented completed repairs following final…

Identified three broken power vent covers where damage exposed the vent housings and allowed water to reach the base flashing and wall assembly. Removed the failed covers and installed new power vent covers at each penetration, restoring proper closure and…

Identified exposed scrim and open seams in the TPO membrane at the source of an active leak. Cleaned and prepped the affected area, applied a two-part urethane base coat over the exposed scrim and surrounding penetrations, then finished with a…

Liberty Roofworks conducted a preventative inspection on a 16-year-old TPO roof in Troutman, NC. They identified membrane wear near roof penetrations and edges, documented the roof's condition, prioritized maintenance, and recommended actions to extend the roof's service life and reduce…

Membrane at the parapet corner had tented, pulling away from the wall and lifting off the deck below. The excess membrane was cut out and removed, the area was cleaned and prepped, and new single-ply membrane was installed across the…

Liberty Roofworks completed a 40,000 square foot commercial roof retrofit in Fayetteville, NC. They installed a Versico 60 mil TPO system over metal roofing with flute fill insulation and a recovery board. The mechanically fastened roof attaches to purlins and…

Liberty Roofworks is restoring a 120,000 sq. ft. industrial facility roof in Roxboro, NC. Services include power washing skylights, installing a custom 24-gauge galvanized ridge vent hood, replacing corroded fasteners, and applying a silicone coating for enhanced moisture protection and…

Liberty Roofworks completed a large-scale metal roof repair on a 120,000 sq ft industrial building in Roxboro, NC. The project involved replacing fasteners, sealing penetrations, fixing 24 leaks, installing a custom ridge cap, and coating fiberglass skylights to extend the…

Liberty Roofworks completed a phased roof replacement in Belmont, NC. They replaced rotted wood beams beneath a 5,000 sq. ft. roof by lifting metal decking in sections. The team installed new LVL beams, ISO insulation, and a new EPDM roofing…