Commercial Roofer in Charlotte, NC

The entry portico on this building had a dented gutter, damaged drip edge and shingles, and fascia and soffit worn out by age and moisture. The crew replaced the sub-fascia and fascia, installed new soffit, drip edge and gutter, and…

This aging flat roof was wearing out, and failed sealant where the coping meets the wall was letting moisture slip under the coping system. The crew cleaned and prepped the joints, applied fresh caulking, and installed a new elastomeric coating…

Ponding water and failing past repairs around a rooftop HVAC unit were letting water in at the curb, penetrations, and mechanical attachments. The crew cleared the water, stripped the old coating from the metal panels, cleaned and primed the surface,…

A fallen tree tore the EPDM section set into this shingle roof and damaged the decking below. The crew cut out the torn membrane, lifted the adjacent shingle courses, and replaced the damaged plywood. New fully adhered 45 mil EPDM…

An open lap in the base flashing at the chimney was giving water a path into the building. The crew cleaned and primed the lap, then installed a new patch to restore a watertight seal, and sealed the chimney seams.…

Damaged shingles along the lower edge of the slope, where the shingle roof meets a low flat section, were leaving the roof open to water. The crew removed the damaged shingles and installed new ones matching the existing profile and…

Loose screws on the metal roof panels, a leaf-clogged gutter outlet, and holes from physical damage were letting water into the building. The crew re-tightened and sealed the fasteners, repaired the damaged holes, and cleared the gutter channel so water…

An unfused membrane seam at a cold weld was letting water under the roof surface, and physical damage had left holes in the membrane. The crew probed the seams, sealed the cold welds, and repaired the damaged holes. Photos show…

Two field leaks on the shingle roof were letting water in where fasteners had been placed incorrectly. The crew carefully removed the specialty shingles, installed new plywood and underlayment, and replaced the shingles to match the existing roof. Photos show…

Poor drainage and added condensation lines were overwhelming the existing system, and one gutter run was damaged or missing. The crew installed new collector heads and downspouts to industry standards and added about 40 feet of new gutter matched to…

Failed coating along a roof valley had cracked open, leaving a split where water could work into the panels. The crew power washed the area, then applied fresh silicone coating along the valley and adjacent spots where the old fluid-applied…

Membrane blistering and heavy wear had split this aged flat roof surface, leaving exposed scrim and openings where water could get in. The crew cut and dried the blistered areas, then installed a roughly 10 by 10 foot TPO recover…

Two failing pitch pans and several small holes in this white single-ply roof were letting water work its way toward the building interior. The crew installed new pitch pans around the pipe penetrations, then cleaned and patched seven holes across…

Weathering had broken down the protective surface on this flat membrane roof, leaving a stained, deteriorated section along the parapet where water could get in. The crew cleaned and prepped a 10 by 15 foot area, then applied a fresh…

Heavy weathering had worn down a large section of this flat roof membrane along the parapet, leaving stained, deteriorated areas open to leaks. The crew cleaned the surface, replaced the worst membrane with new compatible material, and applied a silicone…

Old caulking and flashing along the perimeter of this metal panel roof had cracked and degraded, letting water into the roof system. The crew cut out the failed material, prepped the edge, and applied new caulking and flashing for a…

Degraded spots on this flat TPO roof had worn through to exposed scrim, letting water reach the insulation below. The crew cleaned and prepped each area, then applied a polyurethane base coat and a silicone top coat with taped edges…

Exposed fastener heads, holes in the membrane, and an open seam at the metal edge were letting water into this low-slope roof. The crew sealed seven holes and five exposed fasteners, then cleaned, primed, and covered the separated perimeter seam…

A hole had been torn through the membrane on this flat roof, leaving an open path for water to get into the roof system below. The crew covered the hole with a new EPDM patch that laps onto the surrounding…

Physical damage had punched holes in this flat roof membrane, and two pipe penetrations had not been properly flashed, giving water a path into the roof. The crew repaired the holes with new membrane patches, then sealed the existing penetrations…

The gutter on this low-slope roof edge sat below the drip edge, letting water drip behind it, and a membrane seam had lost its tape sealant. The crew installed new slip metal below the gutter in a matching color, then…

Weathering had broken down a section of membrane along the parapet of this flat roof, where ponding water left heavy staining and the surface layers were peeling. The crew cleaned a 20 by 20 foot area, prepped the deteriorated membrane,…

The filler in the pitch pans around the A/C line penetrations on this ballasted flat roof had shrunk, opening gaps that let water into the roof. The crew installed new lead cover caps on the four pitch pans beside the…

Someone had caulked over an old patch on this membrane roof and the caulk was cracking and peeling, while the sealant around an A/C line penetration had failed. The crew removed the old caulk and installed new membrane patches, then…